Saturday, July 26, 2014

How To Make a Tri-Fold Art Display

tri-fold panel

As promised, albeit much later than I anticipated, here is my "How To" on the tri-fold art display Dwight and I made for our first At Walk show back in May.

We researched a lot of ideas but landed on this as it was a great way to make use of ready-made parts.

menards-frame panels-500px
We bought three of these free standing storage rack frames. They were a good height saved us from making a frame.
menards-frame-closeup-500px

We needed two pieces of pegboard for each frame because they come in 4' x 4' or 2' x 4' sizes but we needed 6' of board to completely cover the frames, so we bought six 2' x 4' sheets.
Panel assembly-parts

Next up: Hardware
Two hinges per connection = 4 hinges, plus plastic feet for the ends (6 total) and lots of 1" wood screws, which we already had on hand.

Finally, some black spray paint. We bought flat black paint and primer in one. I don't remember how many cans we ended up using, but it had to have been at least four. Obviously, you can use any color-and finish- you like!

First up, we sanded the frames. They were ROUGH. They weren't perfect after, but at least we didn't have to worry about getting maimed by giant splinters!
Panel assembly-sanding

Next we cut the pegboard so that we would have some place to screw them in. That is, we had to make sure that the pegboard could be fully supported by a crossmember.
Panel assembly-pegboard

We attached the pegboard to the frames, centering them as closely as we could. Because these frames are meant to hold a 24" board between the supports, the pegboard did not go from edge to edge. It's noticeable when the pieces are raw, but after they're painted, it's not a big deal. This also means that there are no screws along the sides, only horizontally along the cross members.
Panel assembly-pegboard-Dwight

We stood them on end, lining them up to make sure they would fold the right way, then added the hinges.
Panel assembly-hinges
Panel assembly-unpainted

Finally, it's painting time. My least favorite part. We have a well-worn tarp that has seen countless spray-painted projects and bares the scars! We grabbed the paint and had at it, trying to avoid being down wind, and hoping our hands wouldn't cramp up.
Panel assembly-ready to paint-Dwight
Panel assembly-1st coat paint
Panel assembly-1st coat paint-front

After it was completely painted and dry, Dwight added the plastic feet to protect whatever surface these would be on, and they make it much easier to move the screen around once it's up. (You can see them in the very first photo on this post.)

It works great indoors. We haven't tested it outside. I suspect it needs some bracing or strategically placed weights should there be any wind. While it looks fantastic and holds a lot of art, front and back, it does have a few drawback, size being the biggest. It's 6' tall and about 28" wide. Dwight has an Element and we're able to get it in there with the passenger seat all the way forward. Unless you have a similar vehicle or a truck, this is just too big to be hauling from show to show.

We ended up finding a much better solution for us, which I'll share in my next post. Ooooh, cliffhanger!


Supply list and costs
All of this is from Menards:

  • Frames – $11.99 ea x 3 = $35.97
  • Pegboard – $3.99 ea x 6 = $23.94
  • 3" hinges – $2.48 x 2 (2 per pack) = $4.96
  • Spray paint – $3.37 ea x 4 = $13.48
  • 6 plastic feet (can't find receipt)
  • Screws (we already had these)


Friday, July 11, 2014

Seen on my walk

Looks like someone is getting married tomorrow.



In one section of my walk, there are empty, heavily wooded areas on either side of the road. Our neighborhood has a very high water table, including some wetlands, which is why these spaces aren't developed. Reminds me of the lush scenery in The Hunger Games. Clearly someone is using this area as a dumping ground for their yard waste.


And finally, the Queen Anne's lace is in full bloom around here.


Just a few of the things going on in my 'hood.
Related Posts Plugin for WordPress, Blogger...